Top news

Promo centrale vapeur geant casino

We are imageedit, free online photo editor website for everyone.(3) En application du droit de rétractation dont vous bénéficiez en vertu de larticle.Du Code de la Consommation.Vous cherchez un petit appareil de cuisson?La vapeur va réparer les fibres de vos vêtements préférés.Classement, classement en


Read more

Blackjack vs pontoon

You wont get to see them until youve made your move, and theyre then turned over so they can be compared with your hand.Face Up and Face Down Dealers.However, in games that use an eight-card deck, hands like that only turn up every 20


Read more

Cercle de poker lyon

En 2013, il atteint la table finale du 2 200 High Roller du Winamax Poker Tour à Paris, et, en 2014, il finit 3e du 2 200 Deepstack lors des France Poker Séries de Deauville.En janvier 2010, il devient chroniqueur permanent dans l'émission 100


Read more

Upgrade rom monitor slot


As of this writing,.5(4) is the current version and the current file name.
Messages pertaining to the upgrade are displayed on the console.Confirm the current boot variables: show bootvar 2-, specify the new BootLDR to load during boot: conf t boot bootldr bootflash:n 3-, specify the order of the booting images.The following command will show the current/required version: sh hw-module all fpd 8- If the min.Is connected to the switch and is running a FTP server, expecting a username:password of cisco:pass.Use the following command to reset the line card hw-module module 4 reset Router# hw-module module 4 reset Verify the new firmware is running with the command show rom-monitor slot 4 Router# show rom-monitor slot 4 Region F1:approved Region F2:approved, preferred Currently running rommon from.Note, router#show rom-monitor.Next, verify the firmware is ready to run.We use a slightly modified version on the same command show rom-monitor slot X rp Router# show rom-monitor slot 5 rp Region F1:approved, preferred Region F2:invalid Currently running rommon from F1 region Router# The output will display where the active switch processor rommon is running.I always use FTP if possible, due to the higher transfer rates.Chapter 5, rOM Monitor Overview and Basic Procedures.
Ive listed the steps I would typically take to fully upgrade a single Cisco-6509-E (single Route-Processor) with a ipsec VPN SPA blade.
Show logging Verify the firmware is ready to run with the command show rom-monitor slot 5 sp Router# show rom-monitor slot 5 sp Region F1:approved Region F2:first_RUN, preferred Currently running rommon from F1 region Router# Reload the switch reload When the system comes back.Use the show rom-monitor slot 4 command to verify, router# show rom-monitor slot 4 Region F1:approved Region F2:first_RUN, preferred Currently running rommon from F1 region Router# Reset the line card to have the new line card firmware take effect.The list of error commands (Point 5) needs to be corrected, either manually or by using notepad.Before reloading confirm if the SPA FPD code matches the new IOS version.Confirm there are now two config-files (original and new copy disk0: dir disk0: 14- Load the changed config to the startup configuration: copy disk0:new-running-config startup-config 15- Rename the NEW-IOS file back to the original name as listed in the boot command: rename disk0:s72033-adventerprisek9_n 16- Reload.The SUP720 Switch Processor Firmware Once confirmed we can move on to the SUP720 firmware, which is a similar process (where X is the slot your SUP720 is in, (for this example Slot 5) We use a slightly modified version on the same command show.Verify /md5 sup-bootflash:ec.122-17r.SX5 verify /md5 bootflash:n verify /md5 disk0:s72033-adventerprisek9_n it is generally safe practise to backup the working running-config to a file on flash disk0: copy running-config disk0 current-config 1-, lets start, first upgrade the Rom-Monitor: upgrade rom-monitor slot 5 rp file sup-bootflash:ec.122-17r.SX5.Its relatively easy for the image to get corrupted during copying.The field programmable device firmware starts with c6500-fpd-pkg.As of this writing,.2(18r)S1 is the current version and the current file name.122-18r-S1.Router# copy disk0:g bootflash: g Before we reload the switch, we need to make sure the new IOS image is in the same location heads up limit holdem poker is solved as stated above.Router# 19:40:08: DFC4: rommon image upgrade in progress 19:40:08: DFC4: Erasing flash 19:40:11: DFC4: Programming flash 19:40:13: DFC4: Verifying new image 19:40:13: DFC4: rommon image upgrade complete The card must be reset for this to take effect.Router# show rom-monitor slot 4, region F1:approved, preferred Region F2:invalid Currently running rommon from F1 region.For each of these modules: show rom-monitor slot x (where x is the module number from the show module output).




Sitemap